Hydraulic to Vaccum servo conversion

Collapse
This is a sticky topic.
X
X
 
  • Time
  • Show
Clear All
new posts

  • Rocco
    replied
    Originally posted by A80Avant
    powerful, i dont know, but certainly more reliable! no more faffing about brake bombs, and hydraylic fluids anywhere.. Just one pump for the steering, servo in place and if something brakes, a servo is dead cheap to replace and easy.

    Im still waiting from Audi Germany to hear back from the hydraulic servo they sent me which was malfunctioning... I payed 750euros for it... i hope i get some money back.
    the "bomb" cost something like 800€ from AUDI,i asked for it 1 year ago....what a surprise

    you said "some money back"? you should receive ALL money back¡¡

    good luck and thanks

    Leave a comment:


  • A80Avant
    replied
    powerful, i dont know, but certainly more reliable! no more faffing about brake bombs, and hydraylic fluids anywhere.. Just one pump for the steering, servo in place and if something brakes, a servo is dead cheap to replace and easy.

    Im still waiting from Audi Germany to hear back from the hydraulic servo they sent me which was malfunctioning... I payed 750euros for it... i hope i get some money back.

    Leave a comment:


  • Rocco
    replied
    so is this better than the normal sistem? more powerfull and reliable?

    Leave a comment:


  • A80Avant
    replied
    my second pump leaked on the lower of the 2 'X' marked seals, and the other garage should have used some loctite as well but hadnt.

    the 2nd pump although we modified the 2 plugs and used loctite, it didnt leak but was VERY noisy!!! it wasnt working properly at all! I dont know why as well, as when we removed that pump from my car originally it was absolutely fine.

    anyway, as we were ready to fit another dual vane pump which we would modify, we found a single pump laying around, and we thought it would be easier to make a bracket for it and use that rather than worry about leaks from the plugs. It was also 100bar spec and part number was 050145155A which was nicely situated in and didnt make any noises apart from the fact that it only whines a bit after the engine gets warm and only between a small rpm rise from 1300-1800rpm. Then i dont hear it anymore.

    I therefore found a second hand pump which i have sent for inspection and refurb to have aside in case i need to replace it. Otherwise the system works.

    I also noticed that the power steering hose is NLA and only ebay has one for 99euro+shipping and im thinking of getting one to have as a spare.

    I emailed audi tradition as well as they have one with AD ending on the part number instead of AE, and i think its the same hose.

    That way ill be ok if anything brakes down. I have been through a lot with these power steering issues, so much that i was thinking of using an electric steering rack at one point!!haha

    Leave a comment:


  • Pirvu Eugen
    replied
    Hy Vas! I saw on your late pictures that u use different pas pump....
    I had no issues with mine after removing the pistons and plug the hole. What issues you had? Both pumps were damaged?
    Thank You!
    Eugen

    Leave a comment:


  • A80Avant
    replied
    Here is the part number for the LHD power steering hose required:

    893422893AE

    Leave a comment:


  • Rusty
    replied
    Stickified

    Leave a comment:


  • A80Avant
    replied
    no prob! i think it was missing from the forum anyway

    Leave a comment:


  • popdemonic
    replied
    done this on my RHD UrS6 for 2years.So far I'm happy with it.Thanks for your write up.

    Leave a comment:


  • irishs2
    replied
    Thanks for posting this. I too think I will go vaccum on the avant.

    Leave a comment:


  • A80Avant
    started a topic Hydraulic to Vaccum servo conversion

    Hydraulic to Vaccum servo conversion

    I thought this would be of use to someone so here goes.

    After all the ordeal i had with the hydraulic system, i decided to switch to a vaccum assist servo on the rs2. This is a common conversion in the US, and here is the parts list.

    brake booster (4a0 612 107A)
    gasket for booster (431 612 193)
    clevis (893 721 213)
    clevis nut (n011 162 9)
    clevis pin (443 721 371 A)
    check valve (191 611 933 E)

    You also may need the 3b power steering hose from the pump to the steering rack, as it seems to be the only one that fits the LHD cars, otherwise it shouldnt be a problem on RHD cars at all with the hose already there.

    Next is the modification on the power steering pump itself, by removal of the springs and pistons that lie under the x2 marked plugs with the big cross, or X (depends the way you look at it!!)

    In addition, you need to modify the steering rack return hose, which is a simple return, no high pressure one, as well as there is a need of either a T joint or an additional hole to the Inlet manifold to get the vaccum from to the servo.

    Finally, the 2 cables on the hydraulic servo that are meant to measure the pressure in the system and light up the dash, can be left out, covered with tape or heat shrink, but do not hotwire them, as the alarm stays permanently ON.

    I enclose a small pdf description of the modification on an S4

    Hope it helps!
    Vasilis
    Attached Files
    Last edited by A80Avant; 25 September 2011, 19:19. Reason: title word addition
Working...