PIN SWAP i did it, RS4 B7 Coils inside¡

[S2central.net]

Thanks !!!

[Rocco]

what is POS units?

[Rocco]

Rocco my friend.. what happened with yours single coil ECU?
they are not good any more?

this multi coil ECU are not for your car. this is rubbish .. belive me... and B7 coils.. OMG.. rubbish 100% LOL

now I read all posts and thing that I do something wrong, I starts to shaking .. so I went to check it .. and everything is fine.

how could you go and do it on some other "pin swap list" ?
here on forum is perfect one list . which did S2Central ... for now I did 4 pin swap from 3b to aan , and in all cases 100% perfect..

how much did you pay for coils? I can made it for you for maximum 300euro. and BERU coils (2years warenty). you can also tell me,that you will use them on 3B/7A or AAN/ABY valve cover... they will be plug n play..

did engine now run good?

no , the engine dont run nicelly now. i dont know the reason. today will try another ABY ECU

how much for the BERU coils?

[rs200]

in Croatia I can get it for 195 euro 5 piece.

standard OEM AAN coils have 2 POS units before 5 ignition coils.
well "pencile style " (b7rs4) ignition coils have that POS inside of each coil. so they don't need other POS terminals.

if your car don't run good , than you miss some wire (ignition or injector wire.)

if you want I can write to you the whole text "procedure" how to swap wires... step by step.

you know that I do that job few times, why you didn't contact me before you go to own swap? my p.m. have enough space..

[Rocco]

in Croatia I can get it for 195 euro 5 piece.

standard OEM AAN coils have 2 POS units before 5 ignition coils.
well "pencile style " (b7rs4) ignition coils have that POS inside of each coil. so they don't need other POS terminals.

if your car don't run good , than you miss some wire (ignition or injector wire.)

if you want I can write to you the whole text "procedure" how to swap wires... step by step.

you know that I do that job few times, why you didn't contact me before you go to own swap? my p.m. have enough space..

i was thinking that the german guy list would be enough

and dont worry,thank you very much

i am thinking that the problem could come from the ECU or the chips. in some hours i will know more ideas,because Dmitri is coming,he is landing Spain ATM

do you want some beers too? come on,take a fly now.

[prj]

I guess I will be greeted by lots of spaghetti - and I don't mean the edible variety.

[gedu]

Why would you want to put cover over 1.8T coils is beyond me. Either you need full kit of 5 in your trunk, or good insurance and you can always tow your car back home...

[prj]

Buy the coils used on 2.5TFSI (RS3/TT-RS)... they fit well and cost 36 EUR a pop.

[Rocco]

I guess I will be greeted by lots of spaghetti - and I don't mean the edible variety.

i dont understand you what do you want to mean?

[4WheelDrifter]

Rocco, have you also swapped to AAN/ABY FPR and injectors to run with the new 5 coil setup? Or do you have SW to allow for the change?

[rs200]

i was thinking that the german guy list would be enough

and dont worry,thank you very much

i am thinking that the problem could come from the ECU or the chips. in some hours i will know more ideas,because Dmitri is coming,he is landing Spain ATM

do you want some beers too? come on,take a fly now.

hey.. that is good idea.. I will use my private JET , did Pamplona have airport? must ask my pilot .. he will know 100%..

see you at 23 o'clock at airport ..

cheers..

LOL

[UrS4boy]

Rocco: What did you do for the "cam sensor", i.e. Hall Sender? Did you just use the one in the 3B distributor?

[S2central.net]

Rocco - don't tell me you are still running 3B fpr at 3bar - really needs the 4bar part in there from 7A.

[s2_wot]

Buy the coils used on 2.5TFSI (RS3/TT-RS)... they fit well and cost 36 EUR a pop.

That's the 1st time I heard those mentioned. Do they fit under the cover?

[javispa]

Rocco - don't tell me you are still running 3B fpr at 3bar - really needs the 4bar part in there from 7A.

Paul, as far as I know Rocco uses a 7A FPR since he mounted the RS2 turbo.
About the coils, a friend of mine changed his coils and used a R8 ones (which should be the same as the RS4 B7). He told me they worked great and he mounted them without the POS (as some of you have told before).
Cheers.