80Q Competition 20VT inside¡¡

[javispa]

¡Felicidades!

[Sweeper]

On hard load it sounds great , believe me =].
On idle it sounds like you just got to the start line of the circuit WTCC =]

[M_GORDON]

Waiting for... :mischeif:

[CoCaine]

http://www.youtube.com/user/spanishRocco

[ThatGUY]

Audi PCCB brakes : 400x36 & 350x34 & Audi Ceramic calipers + ceramic pads

Are there any part numbers for the rotors?

[Rocco]

Are there any part numbers for the rotors?

ATM i dont have them in my hands.... they are traveling in Berlin

will check it for you whem receive back them

[Rocco]

http://www.youtube.com/user/spanishRocco

http://www.youtube.com/user/spanishRocco#p/a/u/1/39N04gZ6ino

http://www.youtube.com/user/spanishRocco#p/a/u/2/ODqLcrwje6o

could be happening spark problems with the 034 HO "superb" coils.

coil number 3 non working

and i am not sure if my old but new state 3B spark plug wires works well with these coils... because the oem wires from 034 HO coils has different OMS intesity....


anyway,i dont mind,the monday or tuesday i will have 2.5tfsi coils for direct fire ignition without spark wires,hope it works

crossed fingers¡¡¡

[Rocco]

On hard load it sounds great , believe me =].
On idle it sounds like you just got to the start line of the circuit WTCC =]

Vadim it looks like it is pistoning like a competition bike

[Rocco]

i did with my mechanic friend a compression tests in the engine,and these are the results.

i am not an expert of these kind of tests or if they are very good,normal or bad

my friend said it is good. but i would like to share this with you.

i dont remember the order if we started on cylinder one or five.

11 - 11.4 - 10.5 - 10 - 10.5




could be normal??

why appears these numbers whem the pistons were made if i dont remember bad for around 8.0:1 CR ???

[AndyP]

Any updates on this?

[Rocco]

Any updates on this?

yes,everything ready. i only have to wait for my friend Dmitri...

i bought some new sensor for it,like new IAT,Knock sensor,MFTS,N75 and oem ABY 4Bar FPR

because i want to run it with Motronic... it will be safer with Knock sensor function

because HESTEC ECU does not uses them...it is more simple ECU,for example it does not use Altitude sensor,knock sensors,Maf,Narrowband..

[Rocco]

i still have to decide what colour i want to use for repaint the full car

i ti s a very hard decision for me, i dont know what colour and i am sure that after did it i will be thinking that it was a mistake

help please

i´t´s original black paint it is a very dirty colour... always with dust or mud

PD: the car is running well but with a very safe mapping... only 1.3bar ,now waiting for more power

[A80Avant]

altitude sensor? are you going to be doing any hill climbs or drive on the mountains at full boost??

[Zoig]

i still have to decide what colour i want to use for repaint the full car

i ti s a very hard decision for me, i dont know what colour and i am sure that after did it i will be thinking that it was a mistake

RS2 limo in Daytona Grey. I can't decide between this and full black for my UrS6.

Have you tried the "google for random pictures until you find the car colours that look interesting" solution?

[Billman]

altitude sensor? are you going to be doing any hill climbs or drive on the mountains at full boost??

and you are going to have a small turbo and the less dense air is going to overspin it?

We are waiting for your mapping!!!! Get on with it!