Tweet
Quite right! It was the bargain of the year 
-
Nothelle S2 Avant
Black Ur project
Ocianic Ur project gone
S2 Coupe project gone
Urs6 plus project gone -
As I do not have a Tig welder, popped over to see my mate. A small section of the Milltek had been cut off as they apparently could not get the joint apart.
I need to learn this skill.
I can’t wait to hear that lovely 5 pot warble.
Sent from my iPhone using TapatalkNothelle S2 Avant
Black Ur project
Ocianic Ur project gone
S2 Coupe project gone
Urs6 plus project goneComment
-
Arriving at AITP
Sent from my iPhone using TapatalkNothelle S2 Avant
Black Ur project
Ocianic Ur project gone
S2 Coupe project gone
Urs6 plus project goneComment
-
Looked lovely in the flesh , I was parked on the same row but very near the end , unfortunately wasn’t able to put a name to the face ?Comment
-
We need another get together before the summer is goneOriginally posted by simons2 View Post
Nothelle S2 Avant
Black Ur project
Ocianic Ur project gone
S2 Coupe project gone
Urs6 plus project goneComment
-
Milltek fitted. I need to order two new hangers before I can take her for a spin.
Sent from my iPhone using TapatalkNothelle S2 Avant
Black Ur project
Ocianic Ur project gone
S2 Coupe project gone
Urs6 plus project goneComment
-
Man there's so much more room under an avant compared to a coupe!Comment
-
Yes!Originally posted by Bowie69 View Post
It was quite easy to fit but it's slightly too long at the moment. I need to check all the joins are fully home.Nothelle S2 Avant
Black Ur project
Ocianic Ur project gone
S2 Coupe project gone
Urs6 plus project goneComment
-
They tend to hit the rear valence when hot! Stainless expands a lot.Originally posted by Tractor Dave View Post
I used a ratchet strap to pull the centre joint together, get some tension on it then bang it with a rubber mallet.Comment
-
Good plan. Cheers John.
Nothelle S2 Avant
Black Ur project
Ocianic Ur project gone
S2 Coupe project gone
Urs6 plus project goneComment
-
I didn't need the ratchet strap. I had to cut the bolts off the joint clips at the front. A quick spray of wd40 and it moved forward in the joints another 2 inch. Perfect fit now. It must have hung out a lot on it's previous car
Nothelle S2 Avant
Black Ur project
Ocianic Ur project gone
S2 Coupe project gone
Urs6 plus project goneComment
-
Hmmm, interesting. Our 3” Miltek.
certainly not flush, but not 2” out either.85 WR Urquattro, 85 20vT International liveried RallyRep
93 MTMS2 Avant
Comment
-
Just measured mine. Now 2” proud of bumper. Before adjustment it would have been 4”!
I will be listening my old exhaust for sale if anyone is interested. It’s in very good rust free condition.
Sent from my iPhone using TapatalkNothelle S2 Avant
Black Ur project
Ocianic Ur project gone
S2 Coupe project gone
Urs6 plus project goneComment
-
Innuendo Corner.
I’ve just popped out with the tape measure and mine is exactly 2 inches at the top.….
85 WR Urquattro, 85 20vT International liveried RallyRep
93 MTMS2 Avant
Comment
-
Men of our age should be proud of 2"
Nothelle S2 Avant
Black Ur project
Ocianic Ur project gone
S2 Coupe project gone
Urs6 plus project goneComment
Comment