Small Urs6 project!

**maiks** · 9 February 2016, 17:47

Both front shocks were leaking oil.. Bushings seem to be all good, but I already bought Albert's

Front Control Arm Polyurethane Bushings - Audi 100 C4 - Track Hardness

https://www.akmotorsport.net/shop/all-parts/bushings/front-control-arm-polyurethane-bushings-audi-100-c4/

A set for front wishbone for Audi 100 C4. Black set for both front wishbones (left right) of polyurethane bushings. Polyurethane bushings work ideally in performance suspensions. Rubber suspension bushings are a proven compromise in performance vehicles. When additional horsepower is added, plus size tires then OEM or

Front solid subframe bushings for Audi C4

https://www.akmotorsport.net/shop/all-parts/bushings/front-polyurethane-arb-brushing-28-mm-for-audi-c4/

Front subframe solid steel and aluminium bushings for Audi S4 / S6 / UrS4 / UrS6 ( C4 ). It is an upgrade to OEM 4A0399415B and 4A0399419E / 4A0399420E What's included (kit for one car): - two steel mounts for the rear of the front subframe - four aluminium bushings for the front of the front subframe - two M12 steel s

So I only change those, rest of it stays old. Abs sensors also new because they didn't come out and I need to powdercoat all things. Wheel bearings also new.

Little illustrative photo

Attached Files

035.jpg (88.9 KB, 471 views)

**maiks** · 9 February 2016, 18:02

Some kind of rubbers. One was original, the other one was crap. After quick cleaning seems like original is good to go and other one I'll make a new one. These are not available in the store anymore.

Attached Files

**maiks** · 10 February 2016, 18:55

All holes under the bottom are filled with this.

Also under front wings.

Attached Files

**igor136** · 10 February 2016, 19:04

Your plan is to drive this car for another 30 years?

**yannS2** · 12 February 2016, 18:09

How do you proceeded to take out the ball joint to the front arm ????
Thanks

**Pirvu Eugen** · 12 February 2016, 19:46

Just did this today on the 200. Remove the bolt completly, use a wedge to open a little the piece arround ball joint then, huge bar under subframe and on top of arm, press down.

**Thuppu** · 12 February 2016, 20:06

And lift both sides up, then you don't have to press against the sway bar.

Looking good Maiks.

**yannS2** · 12 February 2016, 20:22

How to extract the ball joint
There is a parts of replacement
OEM reference ?

**maiks** · 13 February 2016, 12:20

Originally posted by yannS2

How to extract the ball joint
There is a parts of replacement
OEM reference ?

My poor english cant translate it.

**maiks** · 13 February 2016, 12:26

Originally posted by igor136

Your plan is to drive this car for another 30 years?

Never know.

**maiks** · 22 February 2016, 19:49

New one is bigger

Heat-shrinkable. Little heat and no dust and water can go in.

Thomas's oil sump baffle plate

Attached Files

**maiks** · 24 February 2016, 08:10

Attached Files

**maiks** · 5 March 2016, 10:13

Abs sensors

Shocks

Attached Files

**s0_big** · 5 March 2016, 21:04

Nice

Nice job your doing

Looks wery nice!

**sandman1111** · 5 March 2016, 23:52

how´s the ride with Bilstein b6?

Small Urs6 project!

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment