Coupe Rear ARB options aka FARB on the rear of a coupe

[vertigone]

Whiteline fit 3B yepp... or hmm what do you mean ?

I think the thread is about Coupe FARB in Rear on an S2..

sorry about that I read to fast the title ...

I'll open new post for my question

[andy10v]

Another way of mounting the old style short droplink front arb to the rear, but mounting it to the struts. I had not seen this before.

Cut off the BJ from a droplink, thread and put it through the bush

http://forums.audiworld.com/showthread.php?p=18308889





What is the effect of mounting the same arb, but linked to the struts, or the wishbone?

[martinws]

I would guess that setup would be stiffer if the bars were the same diameter due to less of a lever to twist the bar. I'll get my RARB pics put in here for reference if I remember.

[Error404]

Not much difference in it, the arb mounts to the wishbone and exerts more force because of the shorter lever but has less travel, whereas the strut has more travel but is further from the pivot so exerts less force. I think AndyC worked it out to be about equal in the scheme of things

[Rusty]

That's how Doug did it, I'm sure there's a link right at the start. The issue is that the strut mounts are not that strong, so putting this setup on ripped one of Doug's off. Best to mount to the wishbones IMO.

[v8 coupe]

Bumping this back up because it's a great resource and I have some questions

So I'm currently fitting a setup I pieced together some years ago for a sedan onto my lastest coupe. It is an RS2 front bar and a 25mm arm mounted FARB from a late /89 built 90 which still retained the 2 bolt arms and arm mounted bar.

I had this on my 90 years ago, but never had a chance to drive the car much with it before the 7A died.

If I'm looking at it right this bar is what some 20x the stock bar?

TIA

[betterwith4]

This thread is GOLD and I can't thank you guys enough


I have an aby coupe with kwv1 suspension

I followed this thread and got myself a front anti roll bar of an audi 80 cabriolet with bushes and clamps (rusty helped me find the right one where the ends look hooked)

Took aby rear anti roll bar off swapped struts over left to right right to left


The cabriolet roll bar bolted straight up with standard aby drop links no mods needed at all as mentioned above

Just thought I'd post up letting you know this works with kwv1 aswell as the other suspension variants mentioned

Ps don't comment on the appearance of the underside being a bit on the rough side haha ... not had chance to have it in the body shop or rear 4 pots on yet!

Sent from my SM-G950F using Tapatalk

[stiglet]

Awesome

[Error404]

Holy **** you're alive!

[stiglet]

Holy **** you're alive!

.... and happy to see the forum still going for now I'm just a stalker though

[Error404]

Good to see you are still stalking the threads.
You still got your CQ dude?

[Greg_S]

This thread is GOLD and I can't thank you guys enough


I have an aby coupe with kwv1 suspension

I followed this thread and got myself a front anti roll bar of an audi 80 cabriolet with bushes and clamps (rusty helped me find the right one where the ends look hooked)

Took aby rear anti roll bar off swapped struts over left to right right to left


The cabriolet roll bar bolted straight up with standard aby drop links no mods needed at all as mentioned above

Just thought I'd post up letting you know this works with kwv1 aswell as the other suspension variants mentioned

Ps don't comment on the appearance of the underside being a bit on the rough side haha ... not had chance to have it in the body shop or rear 4 pots on yet!

Sent from my SM-G950F using Tapatalk

Nice work, what is the clearance like on the wishbone ? I had seen references to it being quite tight at full suspension travel.

[betterwith4]

Clearance looked very good nothing touches at all HOWEVER Iv been for a drive and have noticed a very minor knock while going over speed bumps... now I'm going to check it over in a couple weeks time as I'm going away now and car is being picked up for all exhaust redoing (previous owner very bad job) and I'll recheck clearances while on the floor and double check everything's tight should be a minor thing hopefully

Highly recommend doing this with 25mm bar like I have and stock s2 front handles an absolute dream !

Sent from my SM-G950F using Tapatalk

[Bowie69]

If it's the drive shaft or the wishbone, a cut, sleeved and welded up drop link will do you fine!

[betterwith4]

If it's the drive shaft or the wishbone, a cut, sleeved and welded up drop link will do you fine!

Yh I know mate but was trying the standard drop links with my kwv1 suspension as no one has yet I'll move onto shorter links once Iv tried all options so if someone else uses v1 suspension the info will also be here with the rest of it

In the mean time does anyone fancy making me up a set just incase haha

Sent from my SM-G950F using Tapatalk