Titanium Grey S4 Avant

[Vorsprung durch Technik]

No worries mate,hope it all goes well Janis.

[hunker7]

£24 Just measured and short ones are the correct ones. Odd because PN on the other ones matches what 7zap says Anyways, thanks for help Mark. 2 more work days and I can start

[Vorsprung durch Technik]

Could you measure the height of your bumpstops, please

They are 90mm,of the 2.8 quattro, and look the same as the smaller one in your picture,yours are probably bilstein mine are originals and orange in colour same as this link.

http://www.ebay.co.uk/itm/Front-susp...oAAOSwl8NVbvuQ

[hunker7]

Thanks. I was thinking that metal cap goes on the nut but didn't see it on any of my 3 C4's I've had so wasn't sure.

If that collar is included I will probably need it.

Thanks again for info

[Greg_S]

The 2nd from left is a cap for the nut, the plastic disc sits beneath the bump stop. The last one on the left is a collar if your struts are the wider diameter variant.

This should keep me busy for the week and a bit I have off work. Both struts will be coming off and cleaned of rust and painted with some underbody sealant. At the same time I will sort the rust out on wings and clean/spray wheel arches. After that off to Audi for 4 wheel alignment.



I bought bumpstops, and then realised I have some already which are shorter, I assume I must use ones that are shorter due to 1BE lowered suspension?



Also, these came with the shocks, I know where the nut goes (doh!!!) but how about the rest?

[hunker7]

Could you measure the height of your bumpstops, please

[Vorsprung durch Technik]

Think your right,just been out to the shed and the part i had in my hand is the same bumpstop that was in the 2.8 quattro with sport suspension.

Good luck with the weather,i'm in the same boat.

[hunker7]

Hopefully weather will hold I checked 7zap and the bigger ones have the correct PN for AAN/ABH, but the small ones doesn't have any part numbers and not even sure when I bought them. Might need to go over my eBay purchase history and check.

Also ordered new steering damper as mine was very not working

[Vorsprung durch Technik]

That should keep you busy for a while. Based on the bump stops i have in mine atm the small ones are the ones to use.Where did you get them from?

[hunker7]

This should keep me busy for the week and a bit I have off work. Both struts will be coming off and cleaned of rust and painted with some underbody sealant. At the same time I will sort the rust out on wings and clean/spray wheel arches. After that off to Audi for 4 wheel alignment.



I bought bumpstops, and then realised I have some already which are shorter, I assume I must use ones that are shorter due to 1BE lowered suspension?



Also, these came with the shocks, I know where the nut goes (doh!!!) but how about the rest?

[UrS4boy]

Nice project 😃 Do you have interior color code?

Based on that cloth interior being the same as my 94 S4 V8 avant's I would say that the code is: N0D/CK anthracite (black) cloth.

His:



Mine (it's not really purple - the black interiors often photograph with a purple tinge):

[taspamo]

Nice project 😃 Do you have interior color code?

Sent from my MI 4LTE using Tapatalk

[hunker7]

All of us C4 drivers so need the small gauge holders that go into / replace / mimic the centre face vents. I've seen them in photos but cannot trace where to get them as yet.

Would like a boost, air/fuel mixture and a intake air temp gauge. and maybe an oil pressure gauge if a panel was made to accommodate four gauges.

Someone with access to cad and a plastic printer would be able to make up a 'flat' plastic panel to hold four gauges to replace the oem three vent unit, imo.

Just need to find who ?

For some reason don't like replacing vents with gauges Didn't your UrS come with aux gauges from factory? Mine has oil pressure and temperature and clock.

[Spyform]

All of us C4 drivers so need the small gauge holders that go into / replace / mimic the centre face vents. I've seen them in photos but cannot trace where to get them as yet.

Would like a boost, air/fuel mixture and a intake air temp gauge. and maybe an oil pressure gauge if a panel was made to accommodate four gauges.

Someone with access to cad and a plastic printer would be able to make up a 'flat' plastic panel to hold four gauges to replace the oem three vent unit, imo.

Just need to find who ?

just start making the same thing that u are talking about, will show it after it will be made

[macspring]

All of us C4 drivers so need the small gauge holders that go into / replace / mimic the centre face vents. I've seen them in photos but cannot trace where to get them as yet.

Would like a boost, air/fuel mixture and a intake air temp gauge. and maybe an oil pressure gauge if a panel was made to accommodate four gauges.

Someone with access to cad and a plastic printer would be able to make up a 'flat' plastic panel to hold four gauges to replace the oem three vent unit, imo.

Just need to find who ?