Announcement

Collapse
No announcement yet.

New S2 Avant Nothelle N300 owner

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Dave just go to a local bolt and bearing suppler they should be able to get the bolts you need also if you have any problems you can go to them and speak to them face to face. Get a Digital vernier caliper and a metric thread gauge that will help you a lot. Your bolts go M10-1 M10-1.25 M10-1.50 M10-1.75 The finer being M10.1 mm. Maybe that helps a little. Regards Lynn.

    Comment


    • Originally posted by Tractor Dave View Post

      Thanks very much. That info wasn't on 7zap. Are they fine thread? I have a normal thread m10 and it wont go in.
      i can mesure the thread on 2 bolts tommorow. but honestly i think its the normal thread

      Comment


      • Originally posted by rxl

        i can mesure the thread on 2 bolts tommorow. but honestly i think its the normal thread
        You were correct. Normal M10 thread. There was some corrosion on the start of the thread which was causing the problem. All cleaned up and good now.
        Thanks for the good advice.


        Sent from my iPhone using Tapatalk
        Nothelle S2 Avant
        Black Ur project
        Ocianic Ur project gone
        S2 Coupe project gone
        Urs6 plus project gone

        Comment


        • I hope you didn't forget to mount the braket that holds the steering damper. If not they need to come out again

          Comment


          • I did mount it but is it meant to go on the inside of outside of the tie for bracket? Bear in mind my car is RHD and LHD is different set up. It's not clear on 7zap.
            Nothelle S2 Avant
            Black Ur project
            Ocianic Ur project gone
            S2 Coupe project gone
            Urs6 plus project gone

            Comment


            • Originally posted by rxl
              I hope you didn't forget to mount the braket that holds the steering damper. If not they need to come out again
              It’s gone together like this. Hope it’s good.


              Threads had gone on the damper to body mount so I had to put a longer bolt in and an additional nylock nut just above it.


              Sent from my iPhone using Tapatalk
              Nothelle S2 Avant
              Black Ur project
              Ocianic Ur project gone
              S2 Coupe project gone
              Urs6 plus project gone

              Comment


              • Looks correct mate

                Comment


                • Awesome work! Just read through most of your thread. Jealous!

                  Comment


                  • Just a small update. Lots of work but not much to show for it!

                    Finished my brake pipes


                    Hopefully all heading in the right direction!


                    I made a mount for the abs pump. I was missing one and welded something up from my scraps box. Found a rubber bung that fitted inside and it all came together nicely.



                    Sent from my iPhone using Tapatalk
                    Nothelle S2 Avant
                    Black Ur project
                    Ocianic Ur project gone
                    S2 Coupe project gone
                    Urs6 plus project gone

                    Comment


                    • Next job is to refurb this





                      Sent from my iPhone using Tapatalk
                      Nothelle S2 Avant
                      Black Ur project
                      Ocianic Ur project gone
                      S2 Coupe project gone
                      Urs6 plus project gone

                      Comment


                      • Originally posted by Tractor Dave
                        Next job is to refurb this





                        Sent from my iPhone using Tapatalk
                        Done and fitted



                        Where does the carbon canister go?



                        Sent from my iPhone using Tapatalk
                        Nothelle S2 Avant
                        Black Ur project
                        Ocianic Ur project gone
                        S2 Coupe project gone
                        Urs6 plus project gone

                        Comment


                        • Behind the front wing

                          Comment


                          • Ah, I see. I guess that's why the long pipe in the pic on the left of the shield wants to head down into the bottom corner? I take it there should be a grommet it passes through via one of the holes?
                            Nothelle S2 Avant
                            Black Ur project
                            Ocianic Ur project gone
                            S2 Coupe project gone
                            Urs6 plus project gone

                            Comment


                            • 1989 Audi 80 Quattro
                              1994 Audi 80 Quattro Competition

                              Comment


                              • Thanks for the pic. I will try and fit it tomorrow.
                                Nothelle S2 Avant
                                Black Ur project
                                Ocianic Ur project gone
                                S2 Coupe project gone
                                Urs6 plus project gone

                                Comment

                                Working...
                                X