Audi RS2 -94 Swe

[s0_big]

Today i thought it was the big moment when i was going to install the engine in the car. Up early and to the garage only to find out that i didn't find the bolts to the flywheel...
I have papers that i bought new ones but can't remember if i got them or not, anyway i can't find them. So that was a huge dissapointment today. I have order new ones today but i will have to wait a couple of days before they arrive. I managed to mount my turbo today, thought it was easier with the engine out of the car.

45764-e20efe03326d6694df95b39c0a240f22.jpg45764-47028b1b6bb2c4a293a47db17d5dc15a.jpg45764-afdfb1e9e5078dee619371463a36b84b.jpg

[s0_big]

Today i got some flywheel bolts from the Audi dealer. Quick home to the garage to start install the engine. Mounted my reinforced Sachs clutch kit and new throw out bearing.
Intake and all other stuff that was "in the way" was removed. Installation was a little tricky but went well, maybe 20min.

Bolt for flywheel, 1st 30Nm 2nd 90 degres according to manual:
45764-6977aa785a856f017bccfcdd4d6b38c2.jpg45764-36d3a1a0a61bdca13eff0f46361be6d3.jpg
Bolts for pressure plate 25Nm according to manual:
45764-b83bb27b3c50e094cdcb8d4d22d678ce.jpg
Engine installed:
45764-323124377d53805f226d59d87f0e752b.jpg45764-24bfa218106b4678619ee82b9fe9a570.jpg
Can somebody please tell me if this bolt/nut is for tensioning the AC belt? If i use this bolt to tension the belt it will apply pressure to the engine block to tension the belt/bracket, maybe it's right? I can't find anywhere..
45764-ec9edb406000a6cbda4ba6592f87d687.jpg
Tomorrow i will order/pickup stainless hose clamps as i didn't have for all coolant water hoses and pressure hoses. Then i will continue to assemble the engine.

[80Comp]

Looks good.
Bet you can!*t wait to drive it...

[s0_big]

Looks good.
Bet you can!*t wait to drive it...

Thanks. Yeah, sure going to feel good when it's on the road after all these hours!

[SteveH]

Nice bike! I see you're into cycling too Great build, hope you can film the first startup for us

[s0_big]

Nice bike! I see you're into cycling too Great build, hope you can film the first startup for us

Haha! My fathers doughters old bike, if im riding a bike it must have an engine! Yeah, i will sure make a video of the start, good or bad result

[piotr]

Engine is looking fantastic but did you inspected the DMF ?Not 100%sure from the picture but the surface looks like its burn .

[s0_big]

Engine is looking fantastic but did you inspected the DMF ?Not 100%sure from the picture but the surface looks like its burn .

You mean the flywheel? Not burnt, but used! It Will work fine for my original oem power

[piotr]

Yes dual mass flywheel. That's great .As long as you are sure it's not going to cause any judering on pull away .It would be such a pain if you have to pull the box back out again .Lovely job you doing there

[s0_big]

Yes dual mass flywheel. That's great .As long as you are sure it's not going to cause any judering on pull away .It would be such a pain if you have to pull the box back out again .Lovely job you doing there

I don't think it should cause me any problems. If so, it's not that big of a deal to pull the gearbox. My worst fear is that something will be wrong with the engine

[k.alle]

Can somebody please tell me if this bolt/nut is for tensioning the AC belt? If i use this bolt to tension the belt it will apply pressure to the engine block to tension the belt/bracket, maybe it's right? I can't find anywhere..
45764-ec9edb406000a6cbda4ba6592f87d687.jpg
.

Yes, that should be the one.
At least that is how I tension it.

[s0_big]

Work day in the garage!
Assembled the generator/AC/PS-Pump with new belts. Noticed that the belt to the powersteering lies against the brackets a little, just a little, should it be like that?
45764-3994805117b7855700f9fa7514064074.jpg
45764-f354d5cf2ff6d1e9745f26b6eb0a7eb9.jpg
45764-897686994303f16156b903906359c921.jpg
Oilcooler and hoses found it's place, also the holders for the cables, think i got it right :

45764-4ceebc7538c1381200e5029eb970edf1.jpg45764-0f1e0182e8615cd267d2cc87b4c6fc8d.jpg45764-bf418d5bee3f3b6e62db9dc41316d429.jpg
Mounted the IC:
45764-e6fd565ee84174f469e1df01ddc003d1.jpg
Mounted the extra watercooler and the hoses to it:
45764-47bbc8905271908f486fcce13d79f2d9.jpg
Thats all for tonight. Hopfully i will manage to do the start up soon Can't wait to drive it!

[_ShurikeN]

Hi, where exactly is the other end of this cable attached?

45764-bf418d5bee3f3b6e62db9dc41316d429.jpg

Very nice looking motor is coming out, btw.

[piotr]

This is looking so good

[s0_big]

Hi, where exactly is the other end of this cable attached?



Very nice looking motor is coming out, btw.

Thanks! It's going to an earth "plate", red marked location
45764-510dc6d4383780d3aa08c4f591f5018f.jpg